Search results

1993 Super Exceed, 222,000km on body Diesel Auto SLC Utah $20,000 or a solid offer Looking into a new toy so I thought I would put the old girl up here and see if there is any interest. First off this has been my offroad toy and adventure van so the interior reflects that. Only have front...

https://www.saito.it/en/p/turbocharger-kit-sm140-vgt-mitsubishi-hyundai-2-5l-engine-4d56-4d56t Anyone know anything about this VGT turbo made specificly for the 8 valve 4D56? Boost controlled so you don’t need an ecu or two valve controller to run it. Pretty much plug and play.

Has anyone installed the rear TRE210 locker? I have a question about axle end play after installation. Thanks

I have a cold box that I pulled out of my van if anyone is looking for one. Worked the last time I used it but that was years ago.

I'm not much of a transmission guy and looking for some insight on a trans temp issue. I have a 93 L300, 4D56 with auto trans. The trans was overhauled about 30,000 miles ago after the TC grenaded and spread shrapnel throughout the transmission. Since then, I have not had any issues with the...

In search of a rebuildable front diff for my 93 L300 4D56, anyone got a old unit they want to let go off? Thanks

Is there any way to change the front and rear diff gears to 4.10? Along those same lines anyone purchased a locking diff for the front or rear reasently? Looked at the charts but can’t find a part number for the front. Any help appreciated.

Searching for a new oil pan for a 4D56, does not have to be perfect but mounting flange needs to be nice and flat all the way around. Thanks

Looking for the gvw of the l300 campers, can’t seem to find it anywhere. Thanks

Any one know if this tail shaft oil seal can be changed without having to pull the diff gears out?

4d56 l300 super quick glow plugs. Everything was working fine and now I get no clicks. I have no voltage over the signal wire. If I apply voltage to the spade terminal relays click just fine. Any ideas why no signal voltage? Thanks

Is it normal for fuel to come out the return line on the ip pump before it circulates to the injectors? The primer never builds up resistance and you can see the fuel just pumping through the ip body and not going to the injectors. Does this indicate a internal issue with the pump? Is there a...

Need a replacement trim piece if anyone has one they will part with. Let me know, thanks.

1993 Delica Super Exceed 4D56/ Automatic $30,000 500 miles on new engine Frankfort, Ky Well due to the fact that I have to many projects and that we just purchased a bigger van I am putting my delica up for sale. So far she has had quite the life, their are many posts on the site documenting...

Now that I have both engines torn down I thought I would post some pics of the two bare blocks next to each other for comparison. The D4BF does have some extra side material compared to the 4D56 other than that both blocks are pretty much identical. I will say that the casting on the D4BF...

For all you Delica lovers in the midwest there is a new van shop open in Ky specializing in JDM vans. Lunafish Van Works is now open in Frankfort Ky, we do just about everything from mechanical work to full camper build outs. A la Cart items like solar, vent fans, diesel heaters and more. Let me...

Anyone know if the pistons, rods and crank from a D4BF will for a 4D56 block? Thanks

So the van was making a weird noise and continued to blow the crank oil seal out. I decided to take a closer look and tore apart the front end and removed the lower case. What did I find? A cracked block. Now I have had this short block less than a year and has about 12,000 miles on it. I have...

Any idea why the front crank seal keeps blowing out. As soon aa I start the engine the seal blows out. Any ideas? Brand new D4BF short block with new lower case.

So I’m now on my third head from rising sun in Canada. This is a factory Hyundai head so I assume of good quality. If you recall my last head came apart while on the road. In that situation the rocker shaft bolts had pulled out of the aluminum cam cap and caused the shaft to snap. After that I...