Search results

In reading growlerbearnz's detailed post on this, what I have bought (and not installed yet) are the Febest NAB-134 bushings for the uppers (very available). I do not believe you can find OEM uppers anywhere, and these are close (1 mm diameter too big and 6 mm to wide, so they and the receiving...

Thx guys, just ordered the OEM front bearings, OEM tie rod ends (both from Amayama), and the CTR CRM-17 inner tie rods. Also ordered MR389549 front pads (I have the dual piston upgrade), and the rear brake shoes from Karrma. While I was at it, decided to get the new transmission mounts as mine...

Hey gang, got around to having new shocks and tires installed on the '93 L300 4wd Diesel Jasper. On the shock options thread, not sure I saw this model for the front shocks as an option, but I had a hard time finding the Bilsteins in stock, and my mechanic measured and matched KYB KG5603A (put...

I'm struggling to find a website for delicaworks.

Bumping this as it seems like the most recent post on the subject. My upper and lower trans bushings are close to shot. Is there any update on where these bushings may be procured (aside from GBs febest mod for the uppers). Also, I think you need to buy the brackets to get the bushings for...

Hey gang, looking to go with the Billstein front / Monroe Air rear combo when I replace in the not too distant future. Great info here, and thx. My simple question, is adjusting the air in the Monroes as simple as using the same valve fitting on the compressor as I use for my tires. Do not...

so after some fiddling around, and trying to understand why my wiring did not look like what I was hearing here or reading in the manuals, i figured out my blue yellow wire on the harness side that was intended to be plugged into the overheat sensor/shutoff was actually plugged into the black...

i think what is happening is i have a hose without a gauge to start. i am jumping the compressor to feed the refrigerant. after loading a little guy can, i am pulling the charge hose off the fitting and disengaging the jump on the clutch, then using a hand gauge to measure pressure. So in...

so the dash switch works, i can hear the condenser fan kick on (but no compressor clutch). so i think i am down to the engine temp sensor/switch, the dual pressure switch or the ac cutoff. having a hard time getting to pressure switch and engine temp switch. Do i need to take my seat out for...

ok, need a little help here. when i turn on my ac switch on the dash, nothing happens, no change in rpm, no click. just blows warm air. i checked the glass tube fuses with multimeter, all good. i jumped the compressor, clutch kicks, compressor runs. i charged the refrigerant thinking the...

i'll fiddle, thx

I bought and installed these, as the plastic on mine was crumbling. Really helped, but I am unsure on the adjusting. I simply screwed the new ones in. I will tell you, while I had rattle, air, and noise prior, the doors are now closing a bit too tight. You can tell there is a good bit of...

It would remind me of being a kid on a skateboard going down the hill no would would dare and getting the power wobbles.

thx @sk66 and @sck_nogas , part ordered from o'rielly for 6 bucks.

yes, it appears that way

So, based on the reading, I am feeling like it may be nothing more than an ornament. It sounds the D4BF does not have EGR, and I manually control my GP. Might have been the easiest fix yet, if I am correct. Thx!

Hey, newer to the forum, and I can't thank a number of you on here enough. The amount of time and energy saved for a number of completed projects due to the gracious sharing of information and knowledge is just awesome. SK66 in particular has really helped me through the entire fusible link /...

Here is the OEM part if interested. Just curious if there was a metal solution, thx! https://www.amayama.com/en/part/mitsubishi/mb769292

Hey all, new to the forum. Just bought a '93 Jasper and had some rear tailgate latch issues. As advertised, gunked up, outside handle tab that's supposed to be on top of the metal plate somehow got on the wrong side of plate, etc., etc. Appreciate the steer. Wondering if anyone has had luck...