Search results

Can link haz click please Followed by this video

Anyone know where this green wire woulda went & what bulb (if any) went in there? Photo of the headlight backside

The 3-in-1 is reading hot (in my current weather conditions driving 200 is hot) Dashboard gauge looks just fine. Did this for 15 minutes. Then my radio Bluetooth won’t connect. Any accessories flicker. Headlamps & dashboard are fine. Radio flickers off. A minute later back on. I am now parked at...

I’m pulling out my D4BF alternator and needing to rewire my 4D56 male back onto the harness. Like a dingbat, I removed the wires from my connector before noting which end went to which. Anyone have (or can take one) a photo of which wire goes to which side of the male end?

Anyone know the part number for a 4D56/D4BF header Yield/ARP Header Studs?

I recently received my new Denso compressor from @Kellyn. Packaged up nicely and received in good condition. Thank you. I'm beginning to look into the entire R12 -> R134 conversation. I noticed there are conversation kits with adapters for the line connectors also few different parts numbers...

@Kellyn fyi - So my D4BF was purchased in March of 2020. I've had an ever so minor oil leak that I've not been able to hunt down. It's been worsening and now signs of origin are showing above the turbo (and I've not seen oil blow forward and up so this is the only spot it could be. I've taken...

4D56/D4BF Anyone know how this operates? Meaning, is the switch wired to a normally open relay? Is it always sending voltage then the relay closes when the pressure is low (i.e. enough voltage) or is the voltage more of an on/off? I'd check it myself, but it's a hard plug so no back pinning.

Anyone know the secret password or a pro-tip to remove the wiper arms?

Took a long trip. What I hadn't planned on was putting my L300 thru the paces. I have a thing that I won't take my daughter somewhere in the 300 that's further than I've travelled in it. So this past weekend was an opportunity to take the 300 on a 2800 mile round trip. The trip would begin in...

I am (now was) completely ignorant of wheels/studs/lugs & Lug Centric Hub Centric. Sharing a quick story. At 0400 dark thirty I was driving up the 5N in Los Angeles (5 lanes each way) and suddenly began fishtailing. Then my back end dropped with sparks flying everywhere. Watching my 31" fully...

@Growlerbearnz I'm unable to upload photos in the messages... So... reading the LP4 Instructions .... I could only obtain a decent fit flipping the u-bolt; however, the instructions only mention flipping the helper bolt. I tried moving it 50mm forward (per instructions) but the flat bar would...

Anyone have experience either finding new brake lines or purchasing a kit to bend new ones?

I've been asked a few times about my experience in the swap & what I needed. So just sharing my experience. New Parts – Not Required MB581192 & MB581191 Engine Mounts: One is the right side. The other the left side. Don't be penny wise and pound foolish. New Parts – Required MB033054 -...

In need of 1 flexplate for a 4D56 (D4BF) for @Thomb Who haz? Kthx

I splurged again and purchased a non-smoking ashtray holder which surely is sized for Japanese coinage. Agile back I purchased Smooth-On Casting mix who’s original intent was to cast tranny mount bushings ... the window weld is holding up so figure I’m gonna cast it for my locale currency. if...

Reason: I’m not paying $200 to catch spent recycled oil. Parts List: 1x Few feet of hose (designed for diesel & oil) 1x Aluminum Water Bottle 2x 1/2” OD by 3/8” ID Press-to-Connect air hose fittings (to display oil level) 1x 3/8” barbed fitting for breather filter 1x Breather Filter 1x 3/8”...

Problem Statement: Hard battery drain. Post D4BF installation. Negative batter cable disconnected and the interior lights will still come on. Setup: Dual Batteries in parellel Found: When removing the Red fusible link marked for "Lights" the battery does not drain. Also, if the negative cables...

1) Before beginning, we noticed the transmission crossbar Mount was “twisted” and missing 1 bolt on each side. Adjusted & now fully bolted in the crossbar, we pulled the 4D56, swapper parts, dropped D4BF into the bay. 2) Struggling to get the block close enough to the bell housing, we detached...

Tom & I finished the swap today ... sorta. Vehicle fired up straight away. But there was a ticking sound tick tick pause tick tick pause. shut the vehicle off, thought about it, fired up again. Tick tick pause tick tick pause. Shut it off. Tested battery. Now the starter will not engage. All I...