Search results

Hi Y'all! Pinging this thread with some issues. I had some serious squeaking and vibrations after getting my van back from the shop where a new OD solenoid was installed along with some transmission fluid change. They said the fan belt was very loose so they tightened it. Turns out the...

Hey y’all! Pinging this thread and also commented on @Oki-Hai post: https://delicaforum.com/index.php?threads/delica-l300-automatic-transmission-shifting-issues.4870/ Having issues getting out of 3rd into 4th and I suspect it’s the linkage, kick down cable. Jumping up to High rpm then backing...

Hi y’all! Experiencing similar issues. Any help or instructions on adjusting the linkage, kick down cable? Note: previously it was getting into 4th after increasing rpms past 3500 but it was not smooth. Not sure if this is connected but the issue arose when switching overdrive off. Here’s...

Hi y’all! Pinging this thread with a similar issue. For context, just had the engine tuned with EGT gauge installed. Recently had ATF changed with Lucas and took a trip to mammoth mountain (elevation 9,000). On the incline had the overdrive off and was slowed to around 65 kmph with 1200 on the...

Hey team! Pinging this thread to find a pan gasket part number. Would like to find something local.

Hi Steven, what are you selling the OEM for? email: philipjankoski@gmail.com

This is L300 right? Do you happen to have the Camber/Caster bolt/washer part numbers?

Do you have the CTR part number? Did you replace the outers at the same time? Thanks!

Thanks! I'll see if I can find that thread

Hi Y'all, Pinging this thread. Looks like my driverside inner tie rod is loose and causing uneven wear. Should I replace all front Tie Rods and Tie Rod Ends or can I get away with just replacing the one loose inner Tie Rod? Also, is there a decent aftermarket part that could cut cost? I...

Parts question. Pretty sure I need to replace U joints ASAP. Rising Sun quoted around $250 for parts. Do you recommend going this route or could I go aftermarket with this repair? Coombs has AM for $160 out the door.

Thanks, @sk66 went ahead and got the two-pronged sensor that matches with the OEM. Should be ok I hope!

@Sputnik awesome, thanks. I searched EPC and pulled up MD092392. Didn't cross with anything on RockAuto.

Hey @Gardenerguy I have the same aftermarket 12v relay for my 1992 L300 and manual switch. Do you have the Bosch part number by chance? How are they working out? Also considering, @dan NGK CY57 but having trouble finding a source and confirming they are 12V. Concerned about a previous comment...

Hey guys, pinging this thread as the temperature gauge is not working on my Deli and thinking the sensors may need to get replaced. Anyone have a source or link to the parts where I can get them? Thanks in advance!

@dopefish Thanks so much for the info. Steven quoted me a bit higher than that, I suspect COVID related but we will see if he can come down at all. Unfortunately there's a 3 month lead time on the D4BF from Korea.. I am actually in Santa Barbara and I think there's a few techs on the map that...

Sadly I am now reading this thread! Discovered my Intake valve is broken on the first cylinder and the head is cracked as well. Not sure what I should do at this point. Steven from Rising Sun quoted me around $1,300 for a new head. @dopefish wondering what your new engine + radiator was out the...

Looks like I got it to TDC and did the test. I hear air coming out the intake side... I guess it's good (ish) sign there is likely no bottom end engine damage. @Kellyn

Kellyn, thanks for these instructions! I took the glow plug out for the 1st cylinder that wasn't getting compression and put a long nail in there. When I turn the crank shaft manually I haven't really noticed it moving up or down? Is there something I'm missing or does it really need a chopstick!!

One of the rocker arms broke in half. I think this indicates that piston came in contact with at least one of the valves. Valve could have bent and isn’t closing all the way or it could have broke? Hopefully the position is salvageable...