Search results

L300/L400 Ball Joints, set of four Three Five Brand (Japan) lower ball joints with grease fittings. OEM Hyundai upper ball joints with grease fittings installed. Mitsubishi part # MB527351, MB527352. MB527349, MR241623 $300/set; several sets available. Adding zerk fittings to the Hyundai ball...

Rebuilding a Bosch diesel injection pump EXIT • Page bottom • Photoessay originally by bricofoy • Also see Injection • Also see Resealing a Bosch Injection Pump • Downloadable PDF: Bosch VE Pumps.pdf • Reference: Compact Automotive Diesels Yes diesel heads, welcome to...

This is one of those MacGyver tools for the emergency kit bag... I'd almost call it a "must have tool." I like it so much I almost purchased a bunch to resell...

If you have bypassed your glow plug controller, I want it. 6v or 12v, working or non-functional, cash or trade.

I don't, and I wouldn't give up my overhead to have it... but it looks pretty cool; modular, and inexpensive DIY for what it does.

These are brand new alternators made by AS-PL (europe). Each is individually certified on a D&V Electronics test bench and the certification/results are included in the box. No changes are required to the wiring harness/plug. Factory 2yr warranty. I have two 75A which use the 8mm pivot bolt-...

It's just not useful with an automatic transmission. I'd like to pass it on to someone with a manual transmission who can use it; I'd like to get $150 for everything (the valve alone was ~$160). I'll include the modified valve with both flapper plates, gaskets, and wiring (mounts directly to...

Made a little fitting to mount a 12v glowplug in the upper plate on the intake manifold. I retapped the tee m10x1.25 and then cut a little bypass in the seat to allow the boost sensor to function (will mount in the side extension). The relay will get power from the GP relay supply, and will be...

But I know I'm too lazy to pull out the shop vac and an extension cord just to avoid a little mess.

Copied from the tapatalk Mitsubishi 4x4 owners group Fuel pump removal 2.8 fuel pump seal replacement ( Courtesy of R.Ambrose ) Tools and stuff Lots and lots of patients! It took me nearly 3 days. Bear in mind that a lot of places are closed Sunday and are only open Saturday mornings. So I...

Finally got most of the parts together to do a full rebuild of the OEM alternator; parts needed: Seals ME700547 (2ea) Bearings MD611474, MD611476 Regulator MD611668 Rectifier MD611599 Crush Washers MF660063 (2ea, 4 if replacing the line) O-ring ME700951 Unfortunately, all of these parts are...

As posted by @involuted: Here’s everything I’ve learned from troubleshooting throttle valve problems on my Series 2 diesel van! This system isn’t covered in my workshop manual, and my mechanic hadn’t seen it before since Series 2s are still rare in the USA. There’s some good info on the...

Figured out a way to combine these cup holders with the OEM switch panel. Basically, cut the cup holder apart on the table saw, cut the center out of the OEM switch panel, and put it all together using JB-weld black plastic bonder. It just snaps into place in the OEM center console. Pops out to...

I have five 1 sets in stock; price is $120 including shipping in the lower 48.

Finally got a compression tester adapted to the exhaust manifold (replaced EGT probe/plate)... I need to make sure the exhaust brake doesn't generate excessive back pressure resulting in hanging valves. Well, in the driveway I was unable to measure any back pressure; my gauge only has increments...

Went on an off-grid trip last couple of weeks and intermittently the alternator warning lights would come on (batt, water separator, A/T temp). Sometimes it would be very dim, sometimes brighter; seldom for more than a few seconds and never as long as a minute. At all times voltage was fine...

by littlewolfrus

I think I'm going to buy one, just because so many parts are becoming unavailable. The filter is the SIMOTA Racing Sports ZTCA-023 filter, and is supposedly of better quality than the K&N version; but that kind of doesn't matter since the K&N is no longer available. They are telling me it is a...

I bought this EVC 60mm exhaust controller valve off of Ebay... I chose it because I was hoping I could just slip it inline on my DelicaWorks SS exhaust. It also looks to be heavy duty and well built... at least comparatively. I also wanted it to be electric switch control as that's just easier...

Not immaculate, but overall very nice condition and pretty clean, includes the light switch bezel. Dark chocolate brown (can be painted)... I would guess the fabric is faded. Colors in the pictures are accurate (but I cannot say if your monitor is). $150 + sh