Search results

As a backyard mechanic, admittedly a mediocre one, I was thinking about all the wrenching that I've done over the years, all the extra nuts and bolts I've been left with, and all the things I've had to do at least twice before getting it correct. In the moment this can feel like time wasted...

I am looking for the spec for an aftermarket U-joint that will fit our bevel steering gear. I measured stock at 16.6mm - 36T but the closest I can find is 11/16" (17mm) 36T from Borgenson. I busted mine while wheeling a while back and have been working with @13mclean to find a better solution...

Been curious about this for a while. Aside from the slip yoke, are there any differences between the two? What was the benefit to the slip yoke being in the T-Case on the MT vs in the driveshaft like on the AT?

Getting ahead of myself on this but it's on my mind with about a thousand other things. My oil pressure has been dipping when at low idle and also when things are running warm. The little warning light will come on. At some point I will be digging in to replace the water pump and redo all my...

Hey, y’all checking here first. Looking to see if someone has a 3-D scanner, and can capture some things for me. Let me know if anyone would be up for helping.

Looking for Injectors for the 4D56T with a manufacture date before April 1993. Part #MD103301 If you are not sure, PM me with the Japan Vin and I can verify. All 4 is preferable. Thanks!

So things just went up in the air and I was thrown a curve ball. I'm peacing out for a bit and heading overseas for work. Fortunately, it's a Delica haven, but also the belly of the beast right now, Taiwan. I'm going to be putting the van in storage. I have some water leaks that I won't have...

Hey Team, does anybody know if the foot pads for the ladders were the same on top as they were on the bottom? The foot sizes seem to be different and the 2 pads that came on mine only match up to the lower foot exact. Two sources don't sems to have the stock foot pads on, just rubber strips...

***SOLD**** Hey all, selling my Delica Works side dump exhaust. Its great just not going to work for my needs. Everything Is there and in good shape. Never even mounted the side pipe as it wouldn’t mate well with the DreamWorks body lift. I ended up running it center dump for a few months...

***Admin, feel free to shift to another thread if you need.*** Sorry crew, posting this in the L300 thread bc I honestly don't think it will get seen in the non-delica thread. Also, posting this for a friend as I'm currently down with covid, f***!, so not getting my own stuff done. He's got a...

Unfortunately, my balance belt blew up this weekend and threw my timing. Only 40k km on them too. Two hours earlier and I would have been 15miles back in the middle of some BLM land with no one in sight. Super grateful. On the drive home I heard some clanking noise in the top end, pulled over...

I'm doing it. I didn't think I would but I'm biting the bullet and going to install a front locker. In the past there were 2 options that I knew of. 1. get a Lokka Lunch Box locker or 2. find the 8" diff from a gen one Montero and go ARB. Well, there is a third option now. TRE 4x4 is offering...

Hey crew, going to start this off with a few notes first. I am harder on this van than probably most others except for say the Russians and a few Aussies. I am putting my little shoe box through its paces. I am still awaiting feedback from Ironman USA on whether or not they will cover this...

Few items I’ve collected over time, either take-offs or incorrect purchases. All came off a 1989 L300 Turbo - $400, stock good condition. 130k km. Was running 12psi no problem when pulled. Rear AC heater Core - SOLD worked when pulled Turbo Downpipe 4D56 3bolt - free Rear AC vent inlet...

sorry @JohnK, I’ve had a bunch on my plate but managed to dig into this today. First thing you want to do it to pull the switch from the center console and from its own mounting plate. This requires removing two screws from behind. Easy enough. Next you want to pull up the side of the rubber...

I've done a bit of work to my ac recently but am still running into some issues. Mainly it's cool not cold. Here's the rundown. New Denso Compressor Belt to spec Fresh R12 Charge 51oz, pulled vacuum, no leaks. a bunch of fresh o-rings. New Drier. New Fan for lower condenser (from a tw van)...

Stock downpipe and exhaust. No holes just a little rusty. Also have a set of stock leafs that I worn but aren’t running inverted yet. Grab them bring them to a shop for a refresh and then just swap out with yours. Will hold onto this for a week and then will recycle. Located in Santa Cruz...

Left and Right door seals from the Taiwanese Delica. These bad boys are HEAVY DUTY! So much so that the Mitsubishi ones are like 1/2 the weight. My doors were giving me some greifclosing. I just don’t like having to slam things. Otherwise they are great. Quiet and do their job. Mounted up...

This likely exists but I feel like it has likely gotten lost along the way. This is just as much a reminder for those of us who have been around the block and just lost track, as much as it is for the newcomer. USA Karr Automotive/Delicapartsusa.com. @Kellyn @paul Kellyn got this forum up and...

Over the last several months I've been running into the issue where when I'm nearing empty, let's say over 300km on a tank, and I go to start the van up it is like it won't be pulling enough fuel. It will take repeated turning over and sometimes pumping the pedal so when it does catch it injects...